home Cranes and mixers

How to prevent water from dripping from the tap. Preparatory stage and collection of necessary tools. Why the tap in the kitchen flows: find out the reasons

Dripping water from the mixer delivers a lot of trouble to the owners, in addition to the constant pouring sound, bills for payment utilities. If you have a tap in the kitchen or in the bathroom, you can repair it very quickly yourself without resorting to plumbing services.

Causes of Mixer Flow

The reasons for the flow of ball or cartridge water tap, can be very different. For example, very often owners encounter poor-quality shut-off valves. It simply passes the liquid because the locking mechanism does not match the size of the housing or is not worn.

Photo - design of different systems

Also, the quality of the installation plays an important role. Even if the most expensive crane from a well-known manufacturer was bought, an incorrectly twisted valve will cause its sudden breakage. Always with self-assembly follow the manufacturer's instructions. In particular, this is important for unusual models of cranes: sensory, with a timer or other electronics. Here also lies the reason for the frequent problem of incompetent plumbers when hot water flows from a cold faucet. The reasons can be two:

Initially in the crane cold water a hot tube was removed;
Drain channel stop valves and the cold water simply can not get into the spout.

In addition to all external reasons, you need to understand that the crane, like any other device, has its own expiration date. Over time, wear of a gander filter or seal can occur. It should also be borne in mind that with frequent use, threading may be worn.

Photo - a crane in a cut

Video on the topic:

How to fix it

To find out the cause of the leak, you need to disassemble the crane. Depending on the design, the disassembly process may differ significantly, but the basic internal structure of the single-lever and double-lever mixer is very similar. It is necessary to remove the decorative cover and unscrew the valve (or handles at the tap). Just pay attention to the thread, if it is knocked down (or, as they say, slipped), then depending on its condition there are only two options:

Complete dismantling of the mixer and its replacement (in case of serious damage it is impossible to restore this element, of course, if you do not have a tap for cutting);
Sealing threads with a special sanitary tape.

In any sanitary ware shop, such a tape is sold. It is wound on a thread with a strong tension, so it does not interfere with its work, but it is resistant to premature wear and leakage.

Any crane-buksa (Aquafor, Damixa and others) is supplemented with a sealing gasket. It helps to protect the mixer from leaks. Manufacturers perform this part of dense rubber or leather (for expensive models), but both materials are exposed to wear. Negatively, the gasket is affected by the tightness of the valve or the sudden opening of the water.

What should I do if the water tap is running when the water is switched:

It is necessary to disassemble the stop valves. On the crane-bucx you will see a dark element (most often black or brown). This is the gasket;
After a long use, it is very densely pressed on the tap, so it must be pinched by a flat screwdriver in order to remove;
If you do not have the opportunity to buy a new item in the store, you can make it yourself from rubber or dense skin. The main thing is to fully comply with the dimensions of the old gasket;
Under the stop edge, you need to screw the plumbing tape and put the seal over it;
After that the crane body is screwed back, the sealing nut is put on and tightened with a swing or spanner.

It is very important not to tighten the old rotary and half-turn mixer. Otherwise, you can tighten the nut and provoke premature wear of the seal.

Photo - repair of the valve

Most often the tap is closed. Depending on its type, it can be worn ceramic cartridge or a locking metal ball. Correct this trouble only if you remove and replace the locking mechanism.

Photo - replacement gasket

How is the lock replaced during the tap leakage:

Depending on the design, the faucet is dismantled and the constipation is removed. It can be a plate or a ball. When withdrawing, pay attention to their condition - if they are whole, then the reason is different. But, if they are visible cracks or notches, then they need to be replaced;
A fully-sized locking mechanism is selected, experts recommend even finding the same material as in the old one;
In parallel, also check the springs, which are located near the transition from the pipe to the mixer. They can cause leakage of the system and promote fast wear of the constipation.

Another annoyance is the wear of the stuffing box. It comes to light very simply: when the valve closes, nothing drips from the nozzle, but when the mixer is opened from the bottom of the housing (near the nut) water from the pipe starts to flow. Omentum has the property of depressurizing and quickly wear out. To repair it, you just need to fill the part with a sealant. For this purpose, a certain amount of sanitary tape is unwound or the liner is cut from the foil in the form of an oil seal. After the removal, simply fill it in the selected way. The gland nut is also sealed to prevent re-leakage.

Photo - oil seal leaks

Many more home owners face a problem when the toilet flows warm water (say, from a boiler or another heater). Here the reason lies in the fact that the pressure in the riser hot water higher than in the cold, so that water flows from one pipe to the other. For example, it can get into the toilet from the radiator or even washing machine, depending on the quality of the connection. In this case, boiling water does not cause trouble, but the system still needs repair, since the electricity consumption for heating the water is significantly exceeded.

It is very unpleasant if rusty water flows from both faucets (shower, kitchen, etc.). A dirty yellow liquid may indicate the deterioration of the drainage pipe system or the cleaning of sewage by public utilities. This still happens when the water is shut off for a long time. Unfortunately, there is nothing to be done, except how to wait for it to leak and the clean liquid will flow. Use it as a basis for cooking or bathing is strictly prohibited, since it is the habitat of a large number of very dangerous bacteria.

That often many people turn to management companies and invite qualified plumbing. But not always these specialists can wait on time. So, what if there is a tap in the kitchen? How to fix it with your own hands and what tools are needed for this, any home master should know.

Preparatory work

The very first and most important rule for all repairs to plumbing is the disconnection of the water supply. Often, the valves that are responsible for it can be found in the toilet. To turn off the flow, simply turn the tap.

However, due to the fact that there were no problems with the equipment and these cranes were not used for a very long time, the valves can become rusty or blocked. These valves should be developed with the utmost care and very smoothly. Gradually, you can increase the effort, also do not forget about the lubrication. This is the first thing to do before fixing the current tap in the kitchen, in the bathroom and in any other room.

Required Tools

Before work it is important to collect the necessary set of tools. They should be on hand at any time.

So, for work you need a screwdriver with a flat sting and a cross, wrenches. Often, this modest set should be enough. It happens that suddenly and strongly flowing tap in the kitchen. How to fix, what keys it is necessary - here it is impossible to say specifically. The fact is that each manufacturer has its own standards. There will be enough of a set of keys that every motorist has.

Also, it is not superfluous to prepare various additional elements. It can be pieces of rubber, leather, from which you can make gaskets. It can also come in handy fluoroplastic sealant in the form of tape, rags, detergents.

Sometimes in the process of repair, the keys or any other tool can fall - so as not to damage the expensive washing or sink in this way, put a sponge, a rag, or something else that can absorb the shock.

Why there is a tap in the kitchen: how to fix and typical malfunctions

Flowing cranes are quite common.

But there are not so many reasons that can cause a breakdown. There are four most common of them.

Poor quality of the cranes

Often buying plumbing fixtures, many people are guided by considerations of economy and choose products of Chinese or Turkish production. In this case, people are happy that they were able to save this way.

But this tactic when buying mixers is extremely erroneous, and the joy of the saved amount does not last long. This small amount can cause leakage. Well, if at the moment when the crane breaks down, someone will be at home and will soon be able to cut off water or repair equipment. But more often it is different.

You should never economize on such things as plumbing fixtures. Be sure to make sure before purchasing that the offered goods are not made in China, but at least in Russia or in Europe. Also, cheap products for a well-known brand - this is the reason for suspicion. Expensive brand products in our markets are 50% fake.

Sometimes it happens that even on expensive equipment something can leak.

Then it is worthwhile to get acquainted with other reasons to understand how to fix a faucet in the kitchen. Flow also in the case of illiterate erection.

Wrong installation

Here you can also safely turn on production faults or errors in the assembly of the product. If you purchased a high-quality mixer, at a serious price, it's worth to take responsibility for its installation with all responsibility. Various errors that could happen during the installation process can minimize all the advantages of an expensive product.

Violation of operating rules

This is another popular reason. It is very important to remember that the crane, like many other devices and devices, has performance characteristics. If excessive force was applied during use and pressure was applied to the crane details, then do not think that for the device it all went without a trace.

Natural wear of parts

In the course of frequent use cycles, various moving parts of the product may wear out.

Particularly often, various gaskets come into disrepair. In this case, there is nothing easier than to fix the faucet in the kitchen. Flowing? It is enough to replace the gaskets.

The problem with gaskets is more relevant for traditional models with two valves. In the case of a device which is seriously different, you will need another repair scheme.

Crane repair with two valves: replacement of gaskets

How to fix the current tap in the kitchen, if it flows constantly, no matter how tightly twist it - it's all in the worn out gasket. It must be replaced. The first thing to do is twist the valve body - for this, it must be rotated clockwise.

Then remove the damaged seal. If a new gasket is not available, it can be made of rubber or leather. As a sample, it is recommended to use the extracted part. Then a new gasket is put in place of the old one. The sealant is wound on the stopping edge, the valve body is mounted to its rightful place.

For reliability, it is worthwhile to tighten the valve a little with a spanner. In order not to waste time on the process of manufacturing the seal, it is easier and quicker to purchase one in the store or on the market.

We replace the sealing liner on the stuffing box

During use, wear of this liner can trigger leaks. What to do in this case? How to fix a faucet in the kitchen? It flows most often at the moment when the element is open. Water passes between the nut on the stuffing box and the stem on the valve.

Using a screwdriver, unscrew the nut on the stuffing box. Further, a liner is made of PTFE tape. Then it is put in place of the worn out, and the nut is twisted.

If it flows from a spout

Often, a tap flows in the kitchen. How to fix it? Very, very simple. To do this, unscrew the outer nut. Then very gently the spout rotates and rises, and then it is removed. It is necessary to carefully check the insulating gasket and the expansion ring. If something is worn out, a replacement can solve the problem.

Repairing the ball in the kitchen

Fashionable and modern cranes have a more sophisticated device than valve models. How to fix a faucet in the kitchen? Flowing ball valve - means, inside it got any pollution, which does not allow the mixer to work normally.

So, to defeat this problem, the crane is dismantled and cleaned.

The first step is to remove the screw-retainer of the lever. Then very carefully remove the lever. Using a screwdriver, unscrew the screw, remove the dome and the sealant from the plastic.

The latter should be carefully inspected, and the entire plaque removed on it.

If it is worn out, it is recommended to purchase a new part. Then take it out and carefully inspect the ball - if there is damage, a replacement is necessary. When there is a wear of the seals that fix this ball, they are also recommended to be replaced immediately. Then, after replacing parts or cleaning them, all plastic elements should be lubricated by the composition that the manufacturer advises. Sometimes it happens that even after replacing parts, the tap in the kitchen still flows. How to fix it? The repair scheme will be slightly different - here it is necessary to replace the entire cartridge of the crane.

A new tap is running: what should I do?

Sometimes there are such situations. The reason for this phenomenon is industrial marriage. Inside the crane there may be various defects, such as debris or cracks. With their own hands they can not be eliminated. It is necessary to change the product from the seller. Now you know how to fix a faucet in the kitchen. Is the water flowing? This is no longer a problem.

In this article, we will talk about how to fix a dripping faucet in the kitchen or in the bathroom. The topic is of considerable interest, since any plumbing, sooner or later, loses its original working capacity and needs to be repaired or completely replaced.

The problem is aggravated by the fact that the market has a large selection of water taps, which distinguish not only the price and appearance, but also structural features. Therefore, before fixing the faucet, if it drips, it is necessary to determine the varieties of this plumbing equipment presented on the market.

Classification in accordance with functional and structural features

As already mentioned, plumbing equipment is distinguished not only by price and design, but also by design.

All water taps that can be found on the market today are divided into the following categories:

Simple single-element semi-turn devices (turn of the valve is 180 degrees) - designed for the supply of cold or hot water.
Two-ventilatory modifications (mixers) are a design of two coupled single-valued cranes. The temperature and pressure of the water is regulated by opening one and the other tap.
The water supply in the mixers used in the bathrooms can be controlled by means of a "gander" - a common valve installed in the middle.
Single-lever mixer has a design based on the use of a cartridge or ball mechanism. In the adjustment of the head and temperature of the jet is carried out by means of a rotary knob.

Important: Repair of the ball mechanism is possible when you can not restore the working capacity of the cartridges and they can only be replaced.

Mixer with integrated thermostat allows you to set the necessary temperature parameters and maintain them for the required period of time.
In the body of these mixers is placed a thermocouple, which registers the temperature of running water. If the temperature exceeds the set values, the cold water supply turns on, and if the water becomes colder than it needs, the hot water supply starts.
Touch (non-contact) modifications water is supplied when a mobile object appears in the field of action of the photocell. The water temperature in such, most often, is adjusted by means of a mechanical rod on back side housing and does not change during the operation of the equipment.

Repair or change

On the photo there is a swivel and gas key

It is proved that the untimely repair of the stop valves results in the fact that about 15% of the consumed volume of water goes into the sewage drainage. The reason for this is leakage.

The simplest and at the same time effective way to deal with leaks is a complete replacement of the old one with a new one. But the price of such a solution is high - can repairs be more profitable?

As already mentioned, most of the water stop valves can be repaired if necessary. But there is a separate category of equipment that is not designed for repair and is subject to replacement.

For example, cartridge carts can not be repaired, on the other hand, the core of such devices is easy to dismantle and replace with a working part. The devices equipped with a sensor and a thermostat are more complicated by an order of magnitude. To restore the efficiency of such equipment, specialists will need help.

However, there are traditional two-valve and ball versions of the cranes, with the repair of which you are certain to cope and thanks to this you will save money that could be spent on purchasing new plumbing equipment.

Replacement of O-rings

If you have a question about how to fix if the tap is dripping in the bathroom, then most likely you will have to deal with the replacement of the O-rings. The symptom of the problem is the leakage of water from under the flywheel valve.

The instructions for replacing the O-rings are as follows:

We overlap the water supply.
Slot screwdriver or the tip of the knife we support the plug in the upper part of the flywheel. Under the cap is a screw, which we unscrew a curved screwdriver.
After the flywheel is dismantled from the spindle, take the carabiner key on 17 and twist the core.
The core has one or two O-rings of dense rubber. Over time, these rings are deformed and do not provide proper tightness. In place of old rings, you need to install new rings that you can buy in any sanitary ware shop.
Assemblage of the crane is carried out in the reverse order. The core is inserted into the corresponding socket and screwed up to the stop.

Important: Do not apply excessive force to avoid tearing the O-ring.

Now turn on the water supply and see if the repaired faucet passes or not. If there is no leakage, we put on the flywheel and finally we collect the whole structure together.

Replacing the gasket

Now consider how to fix when water drips from the tap by replacing the gasket. The symptom of the problem is leakage from the spout.

Important: Replacement of the worn gasket must be done in a timely manner, otherwise the water will gradually destroy the inside surface of the valve body.
If we neglect the leak, on principle important details The crane is formed by scouring, which can be eliminated by completely replacing the entire device.

The instructions for replacing the gasket are as follows:

Remove the flywheel from the spindle and unscrew the core of the crane using a car key.
The old gasket is located on the opposite end of the core and is fixed there, on a special ledge. We remove the old gasket.
From a piece of dense rubber, we cut out a new gasket, oriented along the contour of the dismantled consumable.
We cut the cut out part into its original place and collect the entire knot together.

Conclusion

So, we looked at a couple of simple examples of eliminating the leak with our own hands. Of course, leakages can also be eliminated on more complex models of mixers, but for this you need to familiarize yourself with the features of their design. It's a little easier to make repairs easier by watching the video in this article.

Any, even the highest quality sanitary ware, eventually goes out of order, and the owners have to face the problem of how to fix a faucet in the bathroom or in the kitchen. It is not necessary to postpone the solution of the issue in a long box, since a running faucet increases the flow of water, and also spoils the appearance of a sink or washbasin, as unpleasant stains appear on it. It is quite possible to repair the crane yourself, no particularly complicated skills or expensive special tools for carrying out this work will be required.

Probably everyone is familiar with this situation, when a tap is dripping in the kitchen or in the bathroom - how to repair the out-of-service equipment? You can, for example, apply to your housing agency with an application to send a locksmith.

But since our communal services are not too hasty, it is likely that the plumbing will have to wait a few days. There is a solution to the problem of applying to specialized firms.

In this case, the specialist will arrive quickly, but the services of such firms, as a rule, are not cheap. The cheapest and, at the same time, "fast" version of repair is an independent performance of work. Consider how this can be done.

How to prepare for repair?

Before you fix a water tap, you should prepare for the work, so that you do not get distracted by trivialities. The preparation process is as follows:

If the packaging has survived from the crane that was acquired once, then it should be found. First, in this box, most likely, an instruction will be found, in which the crane diagram will be given and instructions for repair are given. Secondly, there may be a repair kit, which many manufacturers complete their products.
Now you need to turn off the water supply, shutting off the valve. Disconnect must be served, both hot water and cold.

Advice! If the packing from the tap is not preserved, it's okay. The instructions for repairing the crane will be given below, and the necessary parts can be purchased at any store that sells mixers.

It remains to prepare a basin or other low capacity to collect leaking water and dry cloths for wiping the spray, which are inevitably formed during the repair process.

Advice! For those who have never encountered a crane repair, it is worthwhile to visually see how the work goes if the tap is running and do not know how to fix it - video lessons from detailed description the most important points can be found on the thematic Internet resources.

Repair of a two-valve mixer

Today almost no ordinary cranes are installed, they are replaced by more convenient to use mixers. But the design of the mixers can be different. Consider how to repair a fairly popular model with two valves, one of which regulates the supply of hot, and the second - of cold water.

As a rule, a worm gear hides under the valves, and one of the important elements of this design is a small round rubber gasket. This gasket blocks the inlet, so when it is damaged, the valve starts leaking.

How is the gasket replaced?

When solving the problem, how to fix the current tap, most often, you have to change the damaged gasket.

Advice! Additional gaskets, as a rule, are included in the repair kit for the mixer, they can be purchased separately in sanitary ware shops. In extreme cases, you can make a gasket yourself. Using dense rubber.

Operating procedure:

We unscrew the valve body (the rotation is performed against the clockwise movement).
Remove the worn gasket, install a new one in its place.
Reach any suitable sealant under the edge of the body.
Corps screwed into place, pulling the key.

Carrying out the polishing of the saddle

Sometimes it happens that after installing the gasket, the plumbing works regularly only for a few days, and then the owners again face the problem that the faucet is running - how to fix the mixer in this case?

Most likely, such a situation is evidence that it's time to polish the saddle, that is, the place, in which the rubber gasket rests. During operation, cracks or depressions may form on this part.

To carry out such repairs, you need a cutter - a special cutter installed in the casing. The cutter should be screwed into the place where the worm crane is standing. As a result, all unevennesses will be smoothed out and the newly installed gasket will last for a long time.

Advice! Rotating the cutter is more convenient with a drill, but you can do the work manually.

Features of ceramic taps

Modern cranes instead of whimsical and often broken worm gears are supplied with ceramic discs, so-called crane-bunks. In such cranes there are no rubber gaskets, the water supply is regulated in this case by two ceramic discs equipped with through holes.

When the holes on the disks coincide, water arrives, and if the handle is turned, the holes will shift relative to each other and the water will be reliably blocked. As a rule, cranes of this design serve for years, without requiring repair.

If water leakage is detected, it is usually necessary to tighten the lock nut slightly on the valve body to solve the problem. But if you need to replace the crane-axle, the work should go like this:

With the mixer, remove the flywheel by screwing the plastic plug with a screwdriver. As a result, access to the screw fixing the crane-axle will be opened.
The fixing screw is unscrewed with a Phillips screwdriver with a thin sting.
After removing the flywheel, unscrew the crane-axle with a wrench and remove it.
The installation site should be cleaned with a cloth, and then wrap a new tap-axle.
It remains to collect the crane, performing the operations in reverse order.

Single lever ball valve repair

Today in the bathroom and in the kitchen many prefer to install single-lever mixers. These models are very convenient and reliable, however, their repair involves some difficulties. As a rule, the malfunction of the mixer can be caused by the following reasons:

The internal gasket worn out.
The body of the mixer was damaged.

If a cracks or chips appear on the body, then there can be no question of any repair. The mixer will need to be changed unequivocally. For some time, a crack on the body can try to cover up cold welding or a sealant. But we must remember that this is just a temporary measure, which can help for two or three days.

Replacing the gasket

Now consider how to fix a leaking faucet, if the body is intact and does not cause censures. In this case, it is necessary to replace the inner gasket. Operating procedure:

So, faced with situations when the tap starts to leak, you can solve the problem in two ways. The first way is to contact specialists. That is, you need to turn to a housing office or a specialized firm and call a plumber. Such a decision is relatively simple, but it will take time to wait for a specialist and money to pay for services. The second solution is self-repair. If desired, any person can repair the crane independently.

Leakage of the crane is a common problem, which is not even saved by the availability of quality sanitary equipment. To eliminate the leak, you can call the wizard, but is it worth it to spend money if you can do it yourself? First you need to find out the cause of the malfunction: it can be like wear of the gasket, which is easy and quick to replace, and the failure of the device due to wear or breakage of structural parts.

Common causes of leakage

Before doing any repairs, it is important to find the cause of the problem. There are not so many:

Wear of the gasket is the most common cause of leaks;
Wear a seal on the seal. It is easy to detect a problem. The water, in this case, drips from the valve;
Breakdown of structural parts during long-term operation. Here you need to replace the device.
Initial marriage. It manifests itself in the operation of recently purchased mixers.

In the presence of ball valve The reason for the leak is more difficult to find, since it is difficult to disassemble.

Preparation for work

Regardless of the reason for the tap leakage, it is necessary to carry out preparatory work. First of all, shut the water in the pipes. For this purpose, the valves located in the toilet room are rotated 90 degrees.

Tip . In the event that the valves are not touched for a long time, turning them can be quite difficult. Insufficient load will not allow to turn the valve, excessive can lead to damage to the crane. Therefore, it is recommended to use grease during operation. The valves need to be turned gradually, gently increasing the load.

To perform the work, you will need the appropriate tools:

Adjustable and spanner wrenches;
Flat and cross screwdrivers.

Rubber or leather to replace old gaskets;
Old rags;
Ftoroplastovoy sealing tape, serving as liners;
Sponges;
Universal detergent composition needed to remove dirt in the mixer.

Recommendation . During operation, the tool can easily fall out of the hands, damaging the brittle enamel coating. How to protect the surface of the shell from damage? For this you can use foam rubber or rags. It is enough to put them in the sink, and you can not worry about unpleasant surprises.

Repair of a two-valve crane

How to repair a two-valve crane? The specific nature of the repair work depends on the cause of the leak.

Problem in laying

How to determine what replacement requires a gasket? Try to tighten the tap tightly. If even then it continues to flow, the problem probably lies in the laying. To replace it, do the following:

We remove the valve body. To do this, rotate it counter-clockwise;
We take out the old gasket;
By analogy with the old gasket, we perform a new one. For this we need rubber or dense skin;
The new gasket is inserted into the structure;
The sealant is wound on the stop edge;
The valve body is re-screwed and then tightened with a wrench.

Important . It is not necessary to make the gasket yourself. They can be found in any store with a corresponding focus. Homemade products are usually used when leaks are strong and there is no time to go shopping.

The problem in the packing gland

How can I tell if a leak has occurred because of a worn sealing liner? In this case, leakage is observed near the valve stem. Water begins to flow when the tap is opened. To eliminate the problem, it is recommended to perform the following works:

Unscrew the gland nut. For this we need a screwdriver;
We carry out a new insert from fluoroplastic sealing tape;
We remove old loose leaf. New wind on the valve stem;
The nut is twisted.

Replacement of the packing liner on the stuffing box

Important . When you are finished, try turning the valve. It should turn smoothly. Check also whether leakage is eliminated. Only in this case can we assume that everything is done correctly.

As you can read in a separate article.

Problem with the ring shower hose

In the event that the annular gasket is worn out, there is usually a leak in the hose and mixer connection zone. To fix the problem, you need to do the following:

Carefully, in order not to damage the thread, unscrew the hose. To do this, you need a wrench;
The old seal is removed;
An annular lining is installed;
The hose is screwed.

Tip. To improve the quality and durability of the system, it is recommended to purchase a silicone gasket, as it is characterized by increased resistance to wear.

After the work is done, you should turn on the water and check that the leakage is eliminated. If a small leak is left, it is worthwhile to think about replacing the locking elements (crankboxes). You can buy new locking elements in any sanitary ware shop.

Repair of ball valve

These have many advantages over traditional cranes. But there are also disadvantages. The complicated arrangement of ball valves does not facilitate their disassembly.

The cause of leakage number one, in this case, is usually dirt accumulated in the structure. To eliminate it, it is recommended to perform the following work:

The screw on which the lever is attached is removed. The work is done with a screwdriver;
The lever is neatly removed;
The threaded screw is turned off. This will require again a screwdriver;
Then remove the mixer dome and seal;
The gasket is cleaned of plaque;
In the event that the seal is worn, it should be replaced;
The ball is removed. With its deformations, replacement with a new part will also be required;
With the help of a thin screwdriver, the seals on which the ball is attached are turned away and inspected. Even with slight wear, it is recommended to replace them;
After the old seals have been replaced with new ones, they should be lubricated with a composition suitable for the specific brand of the product;
Produced.

The work on cleaning the ball valve and replacing its worn parts can not only eliminate leakage, but also contribute to a more accurate temperature adjustment.